Restoring your hail damaged vehicle: Hailstorm damage is a car owner’s worst nightmare and can easily be avoided with a few cautionary steps: try to park your car in a shaded or covered area, especially during seasons when hailstorms are prevalent. If you’re going to be going out of town for an extended amount of time, make sure that your car is parked in an enclosed area and, if possible, have someone check on it once in a while. Open spaces will leave your car helpless against the wrath of this natural phenomenon.
In the first place let’s start with some car paint care recommendations: Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.
Decontamination: Life is a jungle out there and the air is filled with unseen pollutants. Never mind the fact that you are breathing these pollutants into your lungs, but the endless particles of pollution is in fact harmful to your car paint. Nest time you have your car washed, glide your hand across the surface of your new car paint ans see if you don’t feel a surface that is less than silky smooth. Most likely you your hand will feel what feels like small particles stuck to the paint that will give it a certain unwanted texture.
Instead, save yourself some of that hard-earned money and do it yourself. There are plenty of ways to get a small dent or ding out of a vehicle at home without ruining your paint, and you don’t need to be a gearhead to do it. However, not all of these tricks will work on your particular automobile; your mileage may vary depending on where the dent is and what your body panel, hood, or bumper is made of (aluminum, carbon fiber, plastic, fiberglass, steel, etc.). For instance, aluminum has little memory properties, so paintless dent removal is much more difficult.
Clay: You could also obtain a better finish and a prominent shine if you use good quality clay. Before the clay is applied to the surface, make sure the car is cleaned with paint cleaner. Always remember to use the right applicator pad or a soft terry towel when working on the car’s exterior, to avoid scratching the vehicle. If you don’t know how to use detailing products or clay on your car, view online tutorials and easy do-it-yourself guides to complete the task easily. Find extra information at Automotive Repair & Customization in Colorado Springs.
PDR is a specialized form of autobody repair where technicians use special tools and techniques to slowly reduce a dent down in size until it completely disappears. PDR is a learned skill. Through trial and error, technicians gradually begin to understand the specific areas of a dent to manipulate, exactly how to manipulate certain locations of a dent, and the specialized processes and technologies used to remove a dent without the need to repaint the area.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.
