Mag drills store Ireland in 2022? Whether you’re a professional contractor or a DIY enthusiast and looking for a metal-cutting tool, this disc is a must-have. The cutting wheel is a great way to quickly cut through metal. With 52 wheels, you’ll always have one on hand. It is compatible with all 4-1/2 inch (115mm) angle grinders with 7/8 inch (22.2mm) arbor. The thickness of the wheel is 0.045 inch (1.2mm). You can operate this up to 13,300 RPM When it comes to precision and burr-free cutting, the Truswe Metal and Stainless Steel Cutting Wheel for Angle Grinder is tough to beat. This ultra-thin design delivers fast and accurate performance, with minimal material loss. The Metal Cutting Discs are made of aluminum oxide grains which are more safe than other wheel types. These discs should only be used when wearing all applicable safety gear because they can fly off the wheel and injure you if not careful. You should read the instructions before using this power tool. It is a heavy duty cutting disc that is fitted to any angle or side grinder. It will cut with ease through sheet metal, plastics, fiberglass, Plexiglas, ceramic tiles and even rubber. Find additional details on arc welders.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.

Several advices about welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.

Even best welder for home use may not be enough for someone who plans on using their MIG welding skills in the workplace. If you’re looking for a high-quality machine that’s ideal for industry-grade jobs, then the Sealey SuperMIG180 may be an excellent choice. Designed as a professional car welder, the SuperMIG180 model is ideal if you’re welding with Argon and CO2. This high-quality model comes with a forced-air solution for cooling inside to make sure that you can extend your welding times without overheating. There’s also a non-live torch fitted into the system so you can reduce the risk of potentially creating arcs when you’re on the move between fast-paced job. Because it’s a professional-level welder, the Sealey SuperMIG also comes with a high-level CO2/Argon regulator, so you can limit your risk of dangerous mistakes as you work. Perhaps one of the easier-to-use small MIG welder options on the market, the Sealey model is very straightforward, particularly for professionals. Although it’s designed for high-level use, there’s nothing to stop you from making the most out of your system within your workshop too. The set comes with an industrial gas regulator, 2 contact tips to choose from, as well as a gas cup. Read extra details at weldingsuppliesdirect.ie.

Power tool pioneers Bosch have been in the game since 1886. They certainly know a thing or two about making one of the best corded angle grinders on the market. I was amazed at the power output and precision you can achieve with the GWS 7-115 angle grinder. Starting off with the look and feel of this grinder, it’s surprisingly slimline and lightweight. It’s certainly easy to hold on to and weighs less than 2 kg. Bosch have made use of a clever 20° angle side handle as well for ultimate precision grinding. Making use of one of Bosch’s brilliant 720 Watt Champion motors, you know this is a tool that’s built to last. Everything is chunky and built for hard work. They’ve included a two-stage safety switch to avoid accidental starts, which is essential for any tool like this. The motor spins a 115 mm cutting disc up to an impressive 11,000 rpm. There’s a relatively low amount of vibration when in use as well. Just 6.5 m/s², which isn’t bad at all for corded grinders. I like the fact that Bosch have flattened the gear head. This reduces the overall size and makes it easy to get into tight spots. If you’re looking for one of the best angle grinders from one of the top names in the business, this is a great choice.

The X-Tractor from Lincoln has a “Mini” in it, which is self-explanatory. The machine isn’t as heavy-duty as most welding fume extractors, but no other device can beat the X-Tractor Mini in terms of portability. The X-Tractor Mini is compact and extremely lightweight. You can just pick it up and set it anywhere you like, from your garage to a store. But, the lighter weight doesn’t compromise efficiency. 2 Different Airflow Settings and 2.4 HP Motor This portable weld fume extractor comes with 2 different settings to choose the preferred airflow. The lower one will generate 95 cubic feet per minute, and the higher one will generate 108 cubic feet of airflow per minute. The amount of airflow seemed a little less to me, but you can’t expect more from a 2.4 HP motor. Besides, the size of the machine speaks for itself that it’s highly portable, which requires a bit of compromising on the power’s end.

Evolution Power tools magnetic drill press is one of the top-rated magnetic drill machines. It is most famous for its lightweight and compactness, excellent and well-constructed magnetic drill machine at a reasonable price. This is ideal for bridges, I-beams, and framework. This can provide 1300 Kgf. Or 2860 lbs f magnetic adhesion. Its maximum core diameter is about 28 mm or 1-1/8 inch. It can give a depth cut maximum of 50 mm or 2 inches. Evolution Power tools magnetic drill press also provide Weldon shank cutter fitting type -19 mm. It also offers a wide variety of tools to be used with Evolution Power tools magnetic drill press. This package includes a wide range of annular cutter, step drills and mini cutters, evolution cutting fluid.

The story of ESAB is the story of welding. When our founder Oscar Kjellberg developed the world’s first coated welding electrode in 1904, he launched a company whose innovation and uncompromising standards have helped create the history of welding itself. For more than 100 years, ESAB has been powered by the will to continuously seek new and improved ways of serving our customers. This has made ESAB a world leader in welding products and advanced cutting systems. In 2012, ESAB was acquired by Colfax Corporation, one of the world’s leading diversified industrial manufacturing companies. Colfax, like ESAB, is a solidly customer-focused company that places strong emphasis on constant innovation and improvement. From the firsts by our founder to our global growth, we take pride in what we’ve accomplished in more than a century. But we do so with a keen eye on the future. What can we do better? It’s only when we seek to build upon all we’ve learned, to perfect the innovations our customers count on to work confidently, and push ourselves and our company further that we can boldly face the future. This is how we continue to write the history of welding and cutting. At the end of the day, it’s not where you’ve been that matters most – it’s where you’re going. And for us, that’s forward.

Our welding tables are to be self-assembled. This is an easy process; full instructions are provided. A wide range of tools are available for use with these tables and they are available as added optional extras in the custom options above. If you require guidance on which tool set would be the most suitable for you please feel free to call our helpful staff. *Please note that current lead times on these welding tables are 3-4 weeks, however if you require the table quicker please alert us and we will do our best to assist with your enquiry*

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

The MIG welder performance depends on several parameters. The duty cycle is among them. It means the percentage of a 10-minute period the welder can work until it gets overheated. For example, “90A / 20%” means that a welder can work for 2 minutes at 90A before an 8-minute cooldown, i.e. 20% of 10 minutes. Now, about the material. We should note that the maximum thickness of a material a welder can handle depends on its amperage and welding wire thickness. Lastly, consider the thickness of the joint a welder can make in a single run. Household models can weld metal sheets from 18-gauge to 1/4” thick at the output of 70A – 180A, respectively.

UK market choice: At just $99, the Goplus is a fantastic value considering what it is equipped to do. In fact, it is the most affordable welder on our list, beating out its competitors by hundreds or even thousands of dollars and putting it in a class of its own. For a budding hobbyist not yet sure if welding is for them, you can’t go wrong with the Goplus. After all, for $99 its welding thickness and the duty cycle is about what one would expect (don’t look to buy this welder if you want it for heavy duty use). The Goplus is light and compact when compared to most other welders. Flux core wire is included. It has four levels of easily adjustable current flow and ten levels of wire speed. The Goplus is able to weld steel and iron at below ¼ inches thickness.

Industrial gas cylinders have been around for a long time. They are widely used for welding, medical applications, fermenting liquids, and several other applications across various industries. In addition to these, new applications for these cylinders are emerging, as new industries and technologies are evolving. These cylinders are filled with low molecular weight chemicals in a gaseous form. Acetylene, oxygen, nitrogen, carbon dioxide, hydrogen, argon, and helium are some gases, which are used regularly. These chemical gases have distinct properties, which are exploited in various industrial applications. If not handled properly, these industrial gas cylinders may be hazardous in various industrial conditions. This post shares some important safety tips for handling industrial gas cylinders in an industrial facility.